EUROLOGIC Voyager 3000 Guia de Instalação Página 158
- Página / 178
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Remote STREAMS Environment
7-12 Fault Tolerant System Administration (R1004H) HP-UX version 11.00.03
Read Krib, PMCB = 0x287b0
Proc Table Starts at 0x2d000
Proc table for rpq_wdog.rel starts at 0x2d334
Code Base for rpq_wdog.rel starts at 0x10b4000
+ [ 0 -ne 0 ]
+ echo /sbin/tomcat/tfinal_init -p 0/3/6/0
/sbin/tomcat/tfinal_init -p 0/3/6/0
+ /sbin/tomcat/tfinal_init -p 0/3/6/0
+ [ 0 -ne 0 ]
+ echo /sbin/tomcat/tfinal_init -p 0/3/4/0
/sbin/tomcat/tfinal_init -p 0/3/4/0
+ /sbin/tomcat/tfinal_init -p 0/3/4/0
+ [ 0 -ne 0 ]
+ [ 0 -ne 0 ]
Tue Nov 14 02:27:14 2000
Child exited with exit status 0 for pid no 697
8. If the new personality has downloaded successfully (as indicated in bold in the
above sample output), skip to step 10. If the new personality fails to download,
an error message is generated.
9. Display the firmware message by entering the following command:
rpqprntf card# -cs
The rpqprntf command reads the error message(s) from the <card>
firmware, and displays a message describing the error. Make any corrections
needed, as indicated by the message, then proceed to the next step.
10. Re-enable the card to ensure it uses the correct personality by entering the
following command:
ftsmaint disable hw_path;ftsmaint enable hw_path
- HP-UX Operating System: 1
- Contents 3
- Revision Information 13
- Audience 13
- Notation Conventions 13
- Product Documentation 16
- Online Documentation 17
- Related Documentation 18
- Ordering Documentation 19
- Commenting on This Guide 19
- Getting Started 1 21
- Using This Manual 22
- Console Controller 25
- Fault Tolerant Design 26
- Duplexed Components 27
- Solo Components 28
- Setting Up the System 2 29
- Installing a System 30
- Configuring a System 30
- Maintaining a System 33
- Overview of the Boot Process 35
- Modifying CONF Variables 40
- Sample CONF Files 41
- Modifying the CONF File 42
- Booting Process Commands 43
- CPU PROM Commands 44
- Primary Bootloader Commands 45
- Booting the System 50
- Issuing Console Commands 51
- <Return> 52
- Manually Booting Your System 53
- <Return> to continue 55
- Shutting Down the System 57
- Using SAM 58
- Using Shell Commands 58
- Changing to Single-User State 59
- Rebooting the System 59
- Halting the System 60
- Activating a New Kernel 61
- Dealing with Power Failures 63
- Managing Flash Cards 65
- Flash Card Utility Commands 66
- Creating a New Flash Card 68
- Duplicating a Flash Card 68
- Mirroring Data 4 69
- Sample Mirror Configuration 71
- Recommended Volume Structure 71
- HP-UX version 11.00.03 5-1 79
- Using Hardware Utilities 80
- Determining Hardware Paths 80
- I/O Subsystem Paths 86
- ■ the logical cabinet 87
- ■ the logical CPU/memory 87
- Defining a Logical SCSI Bus 93
- Determining Component Status 100
- Software State 101
- Hardware Status 103
- Managing Hardware Devices 104
- Error Detection and Handling 105
- Disabling a Hardware Device 106
- Enabling a Hardware Device 106
- Correcting the Error State 106
- Managing MTBF Statistics 107
- Displaying MTBF Information 108
- Clearing the MTBF 108
- Changing the MTBF Threshold 109
- Error Notification 110
- Remote Service Network 111
- Status Lights 111
- Console and syslog Messages 112
- Status Messages 112
- Analyzing System Status 112
- Modifying System Resources 113
- Fault Codes 114
- Saving Memory Dumps 119
- Space Issues 120
- Configuring save_mcore 123
- Configuration 125
- Kernel Configuration area 125
- Analyzing the Dumps 129
- Preventing the Loss of a Dump 130
- Remote Service Network 6 131
- How the RSN Software Works 132
- Using the RSN Software 134
- Starting the RSN Software 135
- Checking Your RSN Setup 136
- Stopping the RSN Software 137
- Sending Mail to the HUB 138
- Validating Incoming Calls 139
- Testing the RSN Connection 139
- Listing RSN Requests 139
- Cancelling an RSN Request 140
- RSN Command Summary 141
- RSN Files and Directories 142
- Communication Queues 143
- Other RSN-Related Files 145
- Remote STREAMS Environment 7 147
- Configuring the Host 149
- Remote STREAMS Environment 150
- Customizing the orsdinfo File 152
- Downloading Firmware 153
- Adding or Moving a Card 155
- New and Customized Software 159
- Console Interface 160
- Flash Cards 160
- Remote Service Network (RSN) 161
- New and Customized Commands 162
- Updating PROM Code B 163
- Updating PROM Code 163
- Updating CPU/Memory PROM Code 165
- Downloading I/O Card Firmware 172
- IndexIndex 173
Manuais e produtos relacionados com Redes EUROLOGIC Voyager 3000
Redes EUROLOGIC Voyager 3000 Manual do Utilizador
(74 páginas)
(74 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais